Skip to end of metadata
Go to start of metadata


Operating SystemAndroid
BSP Release Status

RELEASED

Release Date

  

Repository 
Binariesftp://ftp.phytec.com/products/PCM-051_phyCORE-AM335x/Android/PD14.1.0/
Source Archive 
Release Notes

Click Here




Introduction

This BSP provides a basis for development, deployment and execution of Android based applications on the phyCORE-AM335x System on Module (SOM). For detailed information on the various software components included in the release and how to use them, please refer to the PhyCORE-AM335x Android BSP-PD14.1.0 Release Notes#Quickstart.

Versioning


ComponentVersion
Android 
Linux Kernel 
Barebox 
 


This Release is compatible with the following hardware:

BSP Release VersionBSP Release DateSOM PCB VersionCB PCB Version
PD14.1.0August 4th, 20141358.31359.3

BSP Download

Release PD14.1.0 can be downloaded from the link below.

ftp://ftp.phytec.com/products/PCM-051_phyCORE-AM335x/Android/PD14.1.0/

Quickstart

Release PD14.1.0 should be used in conjunction with the following Quickstart:

What’s Supported

This BSP Release supports the following components:

  • Boot Modes: NAND Flash, NOR Flash, SD/MMC
  • UART: RS-232 on UART_0; UART_1 not tested
  • USB: USB_0-OTG supports ADB; USB_1-OTG enabled for Host mode
  • Ethernet: ETH1 from RMII1 (not stable above 96 Mbit/s)
  • WiFi: TiWi R2 on MMC_2
  • CAN: CAN_0 enabled
  • SD/MMC: MMC_0 enabled; all other MMC not tested
  • SPI driver: SPI_0 enabled
  • I2C driver: I2C_0 enabled
  • EEPROM: at24 on I2C_0
  • PMIC: TPS65910A3 on I2C_0
  • RTC: Internal RTC on I2C_0; TPS65910A3 PMIC on I2C_0
  • Touch:

FocalTech FT5306 (device on LCD-018-070-KAP) on I2C_0STMPE811E (device on Carrier Board) on I2C_0

  • Display:

EDT ETM0700G0DH6 TTL (LCD-018-070-KAP)

  • Graphics: OpenGL binaries under TSPA license

What’s Not Supported

This BSP Release does not support the following components:

  • 10/100/1000 Mbit/s Ethernet on RGMII2
  • RTC: RV-4162-C7 external RTC on I2C_0 - Conflicts with LCD-018-070-KAP touch interrupt
  • Bluetooth: TiWi R2 on McASP1/UART_1
  • Audio: Wolfson Codec WM8974 Line in, Line out, Mic in, Speakers
  • Power Management: Standby and suspend-to-RAM

Fixed in this Release

N/A

New in this Release

  • Touch: FocalTech FT5306 capacitive touch
  • Display:

EDT ETM0700G0DH6 TTL (LCD-018-070-KAP)

Known Issues

  • When using USB_0-OTG in Host mode some devices will not enumerate properly
  • WiFi and ETH1 cannot be used at the same time

Upgrade and Compatibility Information

To upgrade to a new BSP release, simply delete the old release and extract the new release in its place.

Dependencies

N/A

Validation Information

Drivers have been tested with in-house test cases.

Technical Support

For further information or to report any problems, contact PHYTEC Technical Support.