Search

Help

Page 1 of 5. Showing 47 results (0.008 seconds)

  1. How to Add packages to your BSP from an existing recipe

    and add or change labels. Related issues kb-how-to-article … where Yocto can find the source to how it builds the source and where it is deployed. Customizing a BSP is as simple as adding your own meta-layer. You can
    Develop.phytec11 26, 2018
  2. How-to: Request an RMA

    have any questions, you can submit a 'General Product Support' question from the Support Portal home page. Thank you for choosing PHYTEC! how-to rma kb-how-to-article Updated title to conform to new naming scheme.
    Develop.phytec07 17, 2018
  3. How-to: Get schematics for PHYTEC products

    Related articles Related articles appear here based on the labels you select. Click to edit the macro and add or change labels. Related issues kb-how-to-article
    Develop.phytec07 17, 2018
  4. How-to: Find my product serial number

    number 3 edited.jpg The bar code also contains the serial number. kb-how-to-article rma Updated title to conform to new naming scheme. … This how-to will demonstrate how to find product serial numbers for various PHYTEC products. There are a few different formats for PHYTEC product serial
    Develop.phytec07 17, 2018
  5. How-to: Set Up Yocto Plugin for Eclipse

    ) kb-how-to-article yocto eclipse Updated title to conform to new naming scheme. … and debugging applications. This guide will show you how to set up the Yocto plugin for Eclipse to cross-develop applications for Yocto-based PHYTEC BSPs
    Develop.phytec07 17, 2018
  6. How-to: Configure and use Wi-Fi Direct (P2P)

    and add or change labels. Related issues wifi p2p kb-how-to-article Updated title to conform to new naming scheme. … allows for devices to connect and communicate without requiring an access point. This how-to article describes how to enable and test WiFi Direct (P2P) on two
    Develop.phytec07 17, 2018
  7. How To Use SPIDEV on phyFLEX-i.MX6 Yocto BSP

    -frequency = <57600000>; reg = <1>; }; spi@2 { compatible = "spidev"; spi-max-frequency = <57600000>; reg = <2>; }; }; phyflex-imx6 kb-how-to-article Updated title … describe how to clone the kernel source and show how SPIDEV was enabled in the device tree. Note that although the kernel source is available in the Yocto BSP build
    Develop.phytec07 17, 2018
  8. How to Use PHYTEC EEPROM Flashtool with PHYTEC AM572x SOMs

    https://stash.phytec.com/scm/pub/phytec-eeprom-flashtool.git /media/<user>/rootfs/usr/bin/phytec-eeprom-flashtool -b v1.01.00 kb-how-to-article … a single image that supports multiple hardware targets. This How to details the use of the PHYTEC EEPROM Flashtool with PHYTEC AM572x SOMs. The structure, content
    Develop.phytec05 01, 2018
  9. How-to: Run GStreamer pipelines on phyCORE-AM572x

    )24/1, width=(int)1280, height=(int)720' ! h265dec threads=2 ! vpe ! kmssink Related articles Related issues kb-how-to-article phycore-am572x gstreamer Updated … to the LCD power and data connectors at X25. 2. If you are using the PHYTEC VM-009-M12 camera module, install as described in the How-to: Test Camera on the phyCORE
    Develop.phytec07 17, 2018
  10. How-to: Set up WiLink8 WiFi on phyCORE-AM572x

    WiFi network, ping your favorite local device with the following command to verify it is working properly ping -I wlan0 -c 5 <IP addr> Related articles kb-how-to-article phycore-am572x wifi wilink8 Updated title to conform to new naming scheme.
    Develop.phytec07 17, 2018