Introduction
This BSP provides a basis for development, deployment and execution of TI-RTOS based applications on the phyCORE-AM57x System on Module (SOM). For detailed information on the various software components included in the release and how to use them, please refer to the Quickstart.
Versioning
Software
Compatible Hardware
Supported Hardware Versions
Hardware Description | PCB Version |
---|---|
phyCORE-AM57x SOM | 1428.3 |
phyCORE-AM57x Carrier Board | 1435.2 |
BSP Download
Prebuilt images of BSP-RTOS-TI-AM57x-PD17.1.0 can be downloaded from the link below:
BSP-RTOS-TI-AM57x-PD17.1.0 Release
Quickstart
Quickstarts for BSP-RTOS-TI-AM57x-PD17.1.0:
There is no content with the specified labels
BSP Features
Interface | Detail | Tested | Notes |
---|---|---|---|
UART | uart3 | Yes | Connector X18 (default serial console) |
uart4 | No | ||
uart5 | Yes | Connector X17 | |
uart6 | No | ||
uart7 | No | ||
uart8 | No | ||
uart9 | No | ||
uart10 | No | ||
I2C | i2c1 | Yes | Available on expansion Connector X28 |
i2c2 | Yes | Connected to HDMI1_DDC | |
i2c3 | No | ||
i2c4 | No | Used for Audio Codec - available on expansion Connector X28 | |
i2c5 | No | ||
Ethernet | cpsw_emac0 (RGMII0 on SoM) | Yes | RGMII0 - KSZ9031RNX SoM PHY Connector X7 |
cpsw_emac1 (RGMII1 on CarrierBoard) | Yes | RGMII1 - KSZ9031RNX Connector X8 | |
Display and Touch | Analog Touch Control 1 | No | Capacitive: ETM-FT5x06 (on LCD-018), I2C4 |
Analog Touch Control2 | No | Resistive: STMPE811 (on CB), I2C4 | |
PWM Backlight | Yes | ehrpwm0 (EHRPMW1A on CB) | |
24-bit LCD Interface | No | LVDS Connector X25 requires LCD-018 | |
HDMI | Yes | hdmi1_ddc Connector X24 (encoder TPD12S on carrier board) | |
McASP | mcasp1 | No | |
mcasp2 | No | ||
mcasp5 | No | ||
mcasp6 | No | ||
mcasp7 | No | ||
mcasp8 | No | ||
eMMC/SD/SDIO | mmc1 | Yes | Connector X2 |
mmc2 | Yes | eMMC on SOM | |
mmc3 | No | Connector X26 (WiFi/BT connector) | |
USB | usb1 | see Known Issues | USB 3.0 Standard-A Connector X30 (Host only) |
usb2 | see Known Issues | USB 2.0 Mini-AB Connector X9 (device default); signals may also be routed to X19 (Standard-A) | |
CAN | can1 | Yes | DB9 Connector X6 |
can2 | Yes | Pin Header Connector X5 | |
MCSPI | spi1 | No | Connector X28 (Expansion connector) enabled using spidev on X_SPI1_nCS0 |
spi2 | No | ||
spi3 | No | ||
spi4 | No | ||
QSPI | qspi1 | No | NOR Serial Flash on SOM |
SATA | sata1 | No | Connector X11 (SATA) and X12 (power connector) |
PCIe | pcie1 | No | Connector X27 (PI6C557 4x PCIe connector) |
IPU | ipu1 | No | |
ipu2 | No | ||
DSP | dsp1 | Yes | |
dsp2 | Yes | ||
GPIO | User Buttons and LEDs | Yes | |
Memory | EEPROM | No | M24C32 on I2C1 |
NAND (8/16 bit) | No | No NAND populated | |
QSPI NOR Flash | No | N25Q128A connected to QSPI1_CS2 | |
eMMC | Yes | mmc2 on SOM | |
RTC | Internal AM57xx | No | Internal to processor |
PMIC TPS659037 | No | TPS659037 I2C1 | |
External RTC | No | RV-4162-C7 on I2C1 | |
Audio | Stereo Codec on CarrierBoard | No | TLV320AIC3007 codec; connected to McASP1 and I2C4 |
Communication | TiWi-BLE WiFi | No | Connector X26 |
TiWi-BLEBluetooth | No | Connector X26 | |
WiLink8 WiFi | No | Connector X26 | |
Parallel Camera | VIN3 on i2c3 | No | VM-009 at Connector X23 (phyCAM-P connector) |
Hardware Acceleration | Graphics (PowerVR SGX544) | No |
New In This Release
This is the first release so all features supported in the BSP-RTOS-TI-AM57x-PD17.1.0 Release Notes#Features section are new to this release. See below for some specific interface details.
Fixed In This Release
N/A
Known Issues
Texas Instruments Known Issues
Technical Support
For further support please visit PHYTEC's Support Portal