View Source

Operating System	Windows CE
BSP Release Status
Release Date
Repository
Binaries	ftp://ftp.phytec.com/products/PCM-051_phyCORE-AM335x/Compact7/PD13.2.1_EA1/ Important: Pay special attention to your SOM board revision. Due to updated RAM timings, XLDR for SOM revision 1358.2 (PCM-051-12102F0I.A0) should be download from the link below: ftp://ftp.phytec.com/products/PCM-051_phyCORE-AM335x/Compact7/PD13.2.1_EA1/Bootloader/1358.2/
Source Archive
Release Notes	Click Here

Introduction

This BSP provides a basis for development, deployment and execution of Compact 7 based applications on the phyCORE-AM335X System on Module (SOM). For detailed information on the various software components included in the release and how to use them, please refer to the 45646227.

Versioning

Component	Version
Windows Embedded Compact	Based on TI Release BSP_WINCE_A8 2.00.00.01

This Release is compatible with the following hardware:

BSP Release Version	BSP Release Date	SOM PCB Version	CB PCB Version
PD13.2.1_EA1	November 13th, 2013	1358.3	1359.3
PD13.2.1_EA1	November 13th, 2013	1358.2 ^[1]	1359.2

[1] Due to updated RAM timings different software is required to boot the board. Please use BSP Download 1358.2 images that have a modified XLDR version.

BSP Download

Release PD13.2.1_EA1 can be downloaded from the link below.

ftp://ftp.phytec.com/products/PCM-051_phyCORE-AM335x/Compact7/PD13.2.1_EA1/

Important:

Pay special attention to your SOM board revision. Due to updated RAM timings, XLDR for SOM revision 1358.2 (PCM-051-12102F0I.A0) should be download from the link below:

ftp://ftp.phytec.com/products/PCM-051_phyCORE-AM335x/Compact7/PD13.2.1_EA1/Bootloader/1358.2/

Quickstart

Release PD13.2.1_EA1 should be used in conjunction with Quickstart version L-780e_0:

Quickstart

What’s Supported

This BSP Release supports the following components:

Boot Modes: NAND Flash; SD Card
UART: RS-232 on UART_0; UART_1
USB: USB_0-OTG; USB_1-OTG enabled for Host mode
Ethernet: ETH0 from RMII1 (10/100 Mbit/s); ETH1 from RGMII2 (10/100/1000 Mbit/s). Note: Use of ETH0 and ETH1 simultaneously is not supported at this time.
SD / MMC: MMC_0 enabled; all other MMC not tested
CAN: CAN_0 enabled
SPI: SPI_0 enabled
I2C: I2C_0 enabled

EEPROM: at24 on I2C_0RTC: RV-4162-C7 external RTC on I2C_0PMIC: TPS65910A3 on I2C_0TSC: Resistive: STMPE811 on I2C0 (device on carrier board); Capacitive: FocalTech FT5306 on I2C0

Audio: Wolfson Codec WM8974 Line in, Line out, Mic in, Speakers
Display:

HeadlessEDT ETM0700G0DH6 TTL (LCD-018-070-KAP)Prime View PD050VL1 LVDS (LCD-017-050V)Prime View PM070WL4 LVDS (LCD-017-070W)Prime View PD104SLF LVDS (LCD-017-104S)Hitachi TX09D70VM1CCA TFT (LCD-011)

What’s Not Supported

This BSP Release does not support the following components:

Power Management
PRUS

Fixed in this Release

SD card: Implement Card detection interrupt
Splashscreen could now be flashed into NAND Flash through SD Card
MPU Frequency is raised to 720 MHz
Ethernet:

Device hangs after disconnect the Ethernet cableIf the device boot up without connected Ethernet cable it takes 40 seconds more time to boot.

Boot time optimized

New in this Release

Headless support
RAM timing selection support

Known Issues

Sometimes USB OTG Active Sync is not starting. Reboot is necessary
Audio: For some reasons Audio is not working at startup

Workaround: Disable the Windows system sounds to get Audio working on running system.

Upgrade and Compatibility Information

To upgrade to a new BSP release, use the Windows uninstaller to remove the existing BSP via Start->Control Panel->Uninstall a program. Then install the new BSP using the Microsoft installer package or executable, e.g., <device name>-Compact7_BSP_Source-PDxx.x.x.msi.

Dependencies

N/A

Validation Information

Drivers have been tested with a combination of in-house test cases, as well as with the Windows Embedded Compact7 Test Kit (installed along with Windows Compact 7) where applicable.

Technical Support

For further information or to report any problems, contact PHYTEC Technical Support.