This BSP provides a basis for development, deployment and execution of Linux based applications on the phyFLEX-i.MX6 System on Module (SOM). For detailed information on the various software components included in the release and how to use them, please refer to the Quickstart.
This Release is compatible with the following hardware:
|BSP Release Version||BSP Release Date||SOM PCB Version||FLEX Mapper Board Version||FLEX Baseboard Version|
|PD13.2.1||September 5th, 2013||1362.2||1367.3||1364.4|
|1362.1 ||1367.2 ||1364.3 |
|1367.1 ||1364.2 |
 DDR3 and Ethernet layout differences are present. BSP modifications are available to remove Ethernet skew settings that are not required for 1362.1 SOM. Please use BSP Download SOM revision 1362.1 images that have modified versions of Barebox and Linux kernel. Does not fully support PCIe. FLEX Mapper board does not include nPCIe0_PERST. FLEX Baseboard missing 100Ω termination resistor on PCIe clock and reset for an extra PCIe. Hardware interface does not support Camera0 interface extension and full 18-bit Camera0 (missing J6 and J7 for CSI0_DAT3 and CSI0_DAT2 signal multiplexing). Different reset out circuitry for Camera0 and Camera1. JP12 does not exist (X_CAMERA1_CLK & X_CAMERA0_CLK).
Release PD13.2.1 can be downloaded from the link below.
If you have hardware SOM revision 1362.1 the Barebox and Linux kernel images with removed Ethernet skew settings can be downloaded from the link below.
Release PD13.2.1 should be used in conjunction with Quickstart version PD13.2.0:
This BSP Release supports the following components:
Resistive: STMPE811 on I2C0 (device on Baseboard)Capacitive: FocalTech FT5306 on I2C0
Prime View PD050VL1 LVDS (LCD-017-050V)Prime View PM070WL4 LVDS (LCD-017-070W)Prime View PD104SLF LVDS (LCD-017-104S)EDT ETM0700G0DH6 TTL (LCD-018-070-KAP)DVI / HDMI
VM-006-BWVM-009VM-010-BWVM-011-BW (phyCAM-P)VM-011-COL (phyCAM-S)USB-CAM-003H (with UVC Firmware update)USB-CAM-103H (with UVC Firmware update) (without trigger)USB-CAM-051H (with UVC Firmware update)USB-CAM-151H (with UVC Firmware update) (without trigger)
Note: Signal names may change between processor and PCBs. Please refer to phyFLEX-i.MX6 Hardware Manual for signal name mapping.
This BSP Release does not support the following components:
VM-011-BW and VM-011-COL (phyCAM-P and phyCAM-S)new bootargs (configuration possible)individual camera frequenciesExtended gstreamer Examples (mpeg4 decoding by VPU-Hardware and Freescale sink examples for better Bimage presentation[low tearing, low CPU-load])
The BSP is specific to SOM: 1362.2 and Baseboard 1364.4 and will retain compatibility with future released PCB revisions. Workaround is available to use this BSP with 1362.1 SOM; 1367.1 and 1367.2 Mapper, 1364.2 and 1364.3 Baseboard. This BSP is not backwards compatible and has no workaround for 1362.0 SOM and 1364.1 Baseboard due to a change in PCB pinout, see Modification of the pinout for the phyFLEX-i.MX6 (PLF-A-XL1).
Drivers have been tested with in-house test cases.
For further support please visit PHYTEC's Support Portal