|
PHYTEC does not recommend starting new development based on this BSP. Please use the PD15.1.1 release instead. |
This BSP provides a basis for development, deployment and execution of Linux based applications on the phyFLEX-i.MX6 System on Module (SOM). For detailed information on the various software components included in the release and how to use them, please refer to the Quickstart.
|
BSP Release Version | BSP Release Date | SOM PCB Version | CB PCB Version | FLEX Mapper Board PCB |
---|---|---|---|---|
phyFLEX-i.MX6-3.14-PL15.1.0 | 1362.2 | 1364.6 | 1367.3 | |
1364.4 | ||||
1362.1
| 1364.3 [B] | 1367.2 [A] | ||
1364.2 [A] | 1367.1 [B] |
[A] Does not fully support PCIe. FLEX Mapper board does not include nPCIe0_PERST. FLEX Baseboard missing 100Ω termination resistor on PCIe clock and reset for an extra PCIe.
[B] Hardware interface does not support Camera0 interface extension and full 18-bit Camera0 (missing J6 and J7 for CSI0_DAT3 and CSI0_DAT2 signal multiplexing). Different reset out circuitry for Camera0 and Camera1. JP12 does not exist (X_CAMERA1_CLK & X_CAMERA0_CLK).
This BSP is not backwards compatible and has no workaround for 1362.0 SOM and 1364.1 Baseboard due to a change in PCB pinout, see Modification of the pinout for the phyFLEX-i.MX6 (PLF-A-XL1) |
Prebuilt images of imx6-3.14-PL15.1.0 can be downloaded from the link below:
ftp://ftp.phytec.com/products/PFL-A-02_phyFLEX-iMX6/Linux/imx6-3.14-PL15.1.0/
Quickstarts for phyFLEX-i.MX6-3.14-PL15.1.0:
phyFLEX-i.MX6 RDK Quickstart imx6-3.14-PL15.1.0
Interface | Detail | Implemented | Tested | Notes |
---|---|---|---|---|
UART | uart1 | Yes | No | [click for info] |
uart2 | Yes | No | [click for info] | |
uart3 (labelled UART1) | Yes | Yes | enabled - RS-232 on Connector X50 | |
uart4 (labelled UART0) | Yes | Yes | enabled - Connector X51 (default serial console) | |
uart5 | Yes | No | [click for info] | |
I2C | i2c1 (Only used on SOM) | Yes | Yes | enabled |
i2c2 (labelled I2C0) | Yes | Yes | enabled | |
i2c3 (labelled I2C1) | Yes | No | [click for info] | |
Ethernet | 10/100/1000Mbit/s Eth0 from RGMII | Yes | Yes | enabled - Connector X28 |
Digital Audio Multiplexer | AUD3 | Yes | No | [click for info] |
AUD4 | Yes | No | [click for info] | |
AUD5 | Yes | Yes | enabled | |
AUD6 | Yes | No | [click for info] | |
MMC/SDIO | SD1 | Yes | No | [click for info] |
SD2 (Labelled SD1) | Yes | Yes | enabled - Connector X56 | |
SD3 (Labelled SD0) | Yes | Yes | enabled - Connector X57 | |
Communication | TiWi-BLE WiFi on SD3 | Yes | Yes | disabled - Connector X58 (SD3 signals configured for MMC at X57 by default) |
TiWi-BLE Bluetooth | No | No | ||
USB | usb_otg (labelled USB0) | Yes | Yes | enabled - Connector X26 |
usb_h1 (labelled USB1) | Yes | Yes - see Known Issues | enabled - Connector X69 (USB_DN0) | |
CAN | flexcan1 (labelled CAN0) | Yes | Yes | enabled - Connector X52 |
flexcan2 | Yes | No | [click for info] | |
SPI | ECSPI1 | Yes | No | [click for info] |
ECSPI2 | Yes | No | [click for info] | |
ECSPI3 (Labelled SPI0) | Yes | Yes | Enabled - Header X53 | |
ECSPI5 (Labelled SPI1) | Yes | No | Needs pinctrl - Header X30 | |
PCIe | Yes | Yes | Enabled - Connector X59 | |
SATA | Yes | Yes | Enabled - Connector X62, X61 | |
Display and Touch | 24-bit LCD Interface | Yes | Yes | enabled - (Requires LCD-018-070-KAP) Connector X65 |
Analog LCD Touch - Capacitive | Yes | Yes | enabled - Capacitive: ETM-FT5x06 (on LCD-018-070-KAP) | |
Analog LCD Touch - Resistive STMPE811 (on CB), I2C4 | No | Connector X65 | ||
HDMI | No | Connector X40 | ||
PWM Backlight | Yes | Yes - see Known Issues | enabled - Requires LCD-018-070-KAP | |
DVFS | Yes | Yes | enabled | |
GPIO | User Buttons and LEDs | Yes | Yes | GPIO1_30, 2_31, on SOM |
Memory | 8/16-bit NAND Flash | Yes | Yes | enabled |
SPI NOR Flash | Yes | Yes | enabled - N25Q128A13ESE40F on ECSPI3 | |
EEPROM | Yes | Yes | enabled - at24c32 on I2C1 | |
RTC | RTC-8564 Real-Time Clock on I2C2 on carrier board | Yes | Yes | enabled |
Power Management | PMIC | Yes | Yes | enabled - DA9063 on I2C1 |
Audio | TLV320AIC3007 on CB on I2C2 | Yes | Yes | enabled - X11, X8, X10, X9, X7 |
Camera | camera0 on I2C3 | No | ||
Camera1 on I2C3 | No |
[1] It may be possible to change the software configuration to utilize this interface even if it is not being set in the board's default configuration. Please see the External Signals and Pin Multiplexing section of Freescale's i.MX6Q Technical Reference manual for more information on the various modes each pin can be muxed to.
Signal names may change between processor and PCBs. Please refer to the phyFLEX-i.MX6 Hardware Manual for signal name mapping. |
For detailed information regarding the software and hardware interfaces supported in this release: Supported Interfaces Table |
This BSP Release does not support the following components:
Barebox:
Linux:
See here for a list of known issues for the FSL Community Daisy (1.6) BSP Release. imx6-3.14-PL15.1.0 is based on this release.
For further information or to report any problems, contact support@phytec.com.