|
This BSP provides a basis for development, deployment and execution of TI-RTOS based applications on the phyCORE-AM57x System on Module (SOM). For detailed information on the various software components included in the release and how to use them, please refer to the Quickstart.
Components
Compilers
| ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Supported Hardware Versions
| Hardware Description | PCB Version |
|---|---|
| phyCORE-AM57x SOM | 1428.3 |
| phyCORE-AM57x Carrier Board | 1435.2 |
Prebuilt images of BSP-RTOS-TI-AM57x-PD17.1.0 can be downloaded from the link below:
BSP-RTOS-TI-AM57x-PD17.1.0 Release
Quickstarts for BSP-RTOS-TI-AM57x-PD17.1.0:
In the table below highlight supported and tested items with a "Green" box and non supported or un tested or notes issues with a "red" box
| Interface | Detail | Tested | Notes |
|---|---|---|---|
| UART | uart3 | Yes | Connector X18 (default serial console) |
| uart4 | No | ||
| uart5 | Yes | Connector X17 | |
| uart6 | No | ||
| uart7 | No | ||
| uart8 | No | ||
| uart9 | No | ||
| uart10 | No | ||
| I2C | i2c1 | Yes | Available on expansion Connector X28 |
| i2c2 | Yes | Connected to HDMI1_DDC | |
| i2c3 | No | ||
| i2c4 | No | Used for Audio Codec - available on expansion Connector X28 | |
| i2c5 | No | ||
| Ethernet | cpsw_emac0 (RGMII0 on SoM) | Yes | RGMII0 - KSZ9031RNX SoM PHY Connector X7 |
| cpsw_emac1 (RGMII1 on CarrierBoard) | Yes | RGMII1 - KSZ9031RNX Connector X8 | |
| Display and Touch | Analog Touch Control 1 | No | Capacitive: ETM-FT5x06 (on LCD-018), I2C4 |
| Analog Touch Control2 | No | Resistive: STMPE811 (on CB), I2C4 | |
| PWM Backlight | Yes | ehrpwm0 (EHRPMW1A on CB) | |
| 24-bit LCD Interface | No | LVDS Connector X25 requires LCD-018 | |
| HDMI | Yes | hdmi1_ddc Connector X24 (encoder TPD12S on carrier board) | |
| McASP | mcasp1 | No | |
| mcasp2 | No | ||
| mcasp5 | No | ||
| mcasp6 | No | ||
| mcasp7 | No | ||
| mcasp8 | No | ||
| eMMC/SD/SDIO | mmc1 | Yes | Connector X2 |
| mmc2 | Yes | eMMC on SOM | |
| mmc3 | No | Connector X26 (WiFi/BT connector) | |
| USB | usb1 | see Known Issues | USB 3.0 Standard-A Connector X30 (Host only) |
| usb2 | see Known Issues | USB 2.0 Mini-AB Connector X9 (device default); signals may also be routed to X19 (Standard-A) | |
| CAN | can1 | Yes | DB9 Connector X6 |
| can2 | Yes | Pin Header Connector X5 | |
| MCSPI | spi1 | No | Connector X28 (Expansion connector) enabled using spidev on X_SPI1_nCS0 |
| spi2 | No | ||
| spi3 | No | ||
| spi4 | No | ||
| QSPI | qspi1 | No | NOR Serial Flash on SOM |
| SATA | sata1 | No | Connector X11 (SATA) and X12 (power connector) |
| PCIe | pcie1 | No | Connector X27 (PI6C557 4x PCIe connector) |
| IPU | ipu1 | No | |
| ipu2 | No | ||
| DSP | dsp1 | Yes | |
| dsp2 | Yes | ||
| GPIO | User Buttons and LEDs | Yes | |
| Memory | EEPROM | No | M24C32 on I2C1 |
| NAND (8/16 bit) | No | No NAND populated | |
| QSPI NOR Flash | No | N25Q128A connected to QSPI1_CS2 | |
| eMMC | Yes | mmc2 on SOM | |
| RTC | Internal AM57xx | No | Internal to processor |
| PMIC TPS659037 | No | TPS659037 I2C1 | |
| External RTC | No | RV-4162-C7 on I2C1 | |
| Audio | Stereo Codec on CarrierBoard | No | TLV320AIC3007 codec; connected to McASP1 and I2C4 |
| Communication | TiWi-BLE WiFi | No | Connector X26 |
| TiWi-BLEBluetooth | No | Connector X26 | |
| WiLink8 WiFi | No | Connector X26 | |
| Parallel Camera | VIN3 on i2c3 | No | VM-009 at Connector X23 (phyCAM-P connector) |
| Hardware Acceleration | Graphics (PowerVR SGX544) | No |
This is the first release so all features supported in the BSP-RTOS-TI-AM57x-PD17.1.0 Release Notes#Features section are new to this release. See below for some specific interface details. |
N/A
Texas Instruments Known Issues
For further support please visit PHYTEC's Support Portal